3DJAKE Adheasy Spray, 400 ml
Ultimate adhesive for a wide variety of materials
Features & Advantages
- Easy application
- In a large 400ml can
- For heated and unheated build surfaces
Item no.: APP-ADHEASYSPRAY, Content: 400 ml, EAN: 9120078088012
Product information & technical details
- Item no.: APP-ADHEASYSPRAY
- Manufacturer No.: ADHEASYSPRAY
- Manufacturer: 3DJAKE
- Content: 400 ml
- Product type: 3D Printer Accessories
Description
Adheasy Spray is the perfect solution to warping!
The specially developed formula works great with many different materials.
The spray can be easily applied to heated or unheated beds.
Once the board has cooled down after printing, the model can be easily removed.
Advantages of the Adheasy Spray:
- Easy application
- Works with many materials
- For heated and unheated building boards
- Easy cleaning
Application:
- Preparation: Clean the build plate and shake the spray bottle
- Application: Apply the Adheasy Spray at a distance of about 20cm to the build plate.
- Print: The right levelling and the Adheasy Spray ensure optimum adhesion
- Removal & Cleaning: The model can be easily removed after cooling the plate and the adhesive can be removed with an alcohol-based cleaner
Hazard and precautionary statements
Signal word: Danger
Precautionary statements:
- P101 - If medical advice is needed, have product container or label at hand.
- P102 - Keep out of reach of children.
- P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P211 - Do not spray on an open flame or other ignition source.
- P251 - Do not pierce or burn, even after use.
- P410+P412 - Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
- P501 - Dispose of contents/container at a special hazardous waste collection point.
Hazard statements:
- H222 - Extremely flammable aerosol
- H229 - Pressurized container: may burst if heated
- H319 - Causes serious eye irritation
Product videos:
Questions & Answers about 3DJAKE Adheasy Spray
-
Is it a good idea to use this with Nylon PA12? Can you use it on all bedtypes (including smooth PEI and powder coated sheet)?
Customer Reviews
1 English review written for 3DJAKE Adheasy Spray
70 customer reviews in all languages
| 5 stars | | 140 | (86%) |
|---|---|---|---|
| 4 stars | | 14 | (8%) |
| 3 stars | | 5 | (3%) |
| 2 stars | | 1 | (0%) |
| 1 Stars | | 1 | (0%) |
161 reviews
1 customer review in English
70 customer reviews in all languages
-
Goran Visnjic, Slovenia
08 June 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Very useful companion that should be beside every 3D printer
Rated with 5 out of 5 stars.
This was my first purchase of any build plate adhesion promotor. I was skeptical about this things and looked at them as another way to pull extra money from my wallet. If I used right build plate and right temperature, my prints always sticked pretty well to the build plate and were easily released after cool down.
Since it was relatively cheap and had good reviews I decided to give it a try. If anything, just out of curiosity.
Well, this thing works and works well. It supports laziness in some way, because it makes your selection of build plate surface material and build plate temperature less critical. In 90% cases with common materials, you do not have to tune your build plate temperature settings to be spot on.
It can be easily cleaned with methanol (maybe with other alcohols too, haven't tried).
Try not to spray it over your linear guides and other sliding elements if you spray directly on installed build plate, because it leaves thin layer of adhesive (as it is supposed to do), and you might run into problems after certain amount of careless spraying sessions.Was this rating helpful? (0) (0)
Warm to hot water will remove this from a glass plate easily. You can use alcohol too but water is free :)